CT Turbo S wheel arches

[Domy69]

You need the gloss black ones from the turbo S. Those are easier to paint, the others have a structure they need to sand and probably add a base layer. Where did you order? Mine was done in Latem.

I ordered it from Kronos LLN. It has been in production status since February 02!! how long did you have to wait when the car was at the importer in Belgium?

Sponsored

 

[McgR]

I ordered it from Kronos LLN. It has been in production status since February 02!! how long did you have to wait when the car was at the importer in Belgium?

I think around a week from Dieteren to the dealer. Apparently this is a random process that can aslo take longer. They say they don’t know when it will be shipped to the dealers.

 

[ze_shark]

So i am in the middle of this, and it is a bit confusing.

I started from this helpful list:

1	9J0-853-135-BY-G2X
2	9J0-853-136-BY-G2X
3	9J0-853-717-CY-G2X
4	9J0-853-718-CY-G2X
5	9J0-853-817-GY-G2X
6	9J0-853-818-GY-G2X
7	9J0-853-817-EY-G2X
8	9J0-853-818-EY-G2X
9	9J0-854-819-EY-G2X
10	9J0-854-820-EY-G2X
11	9J0-854-829-AY-G2X
12	9J0-854-830-AY-G2X
13	9J0-854-731-AY-G2X
14	9J0-854-732-AY-G2X

But something does not make sense.
Charts show 7 parts on each side:

But pictures stubbornly show 3 parts on the front side. not 4. I can see why the part numbers would be different with/without ultrasonic sensors, but part 3 above in the assembly view does not seem to comport with any Cross Turismo configuration ?

(web picture, my car is in transit but even the 3D configurator shows the same config)

So issue #1 is whether the correct combination is 12 parts, which 12 (minus those belonging to position 3 above ?).
Issue #2 iswhether position 1 also has an option with/without ultrasonic sensor ?

And did anyone find the spec of the VHB adhesive to use to avoid delamination ?

Help much appreciated !

 

[Regular]

So i am in the middle of this, and it is a bit confusing.

I started from this helpful list:

Charts show 7 parts on each side:

But pictures stubbornly show 3 parts on the front side. not 4. I can see why the part numbers would be different with/without ultrasonic sensors, but part 3 above in the assembly view does not seem to comport with any Cross Turismo configuration ?

I'm guessing that #3 is if the Offroad Design Package (ODP) is optioned. Here is the front right wheel ODP moulding from an eBay listing (https://www.ebay.co.uk/itm/145726089267):


Left is down, #3 is on the lower right

To get an overview, check this link to all the trim parts for TurboS: TurboS compatible
(edit: changed link to TS).

 

[ze_shark]

Thank you very much for sharing this link. The problem is that it does not give 12 or 14 primed part numbers. It gives .... 20 ! The description of the VHB tape PN is very useful, but for the selection of wheel arches, the list which @McgR shared is still the most credible source for primed parts in what appears to be my configuration.

I am also puzzled by the parker screw and washer situation. The diagram points to them being used at the ultrasonic sensor location, and i don't get why, furtherless why @McgR dearler would have used 25 of them. Could it imply that the whole fender liner has to be removed to access the ultrasonic sensor from behind ?

Sponsored