Sold: Taycan Sun Visor Safety Notice Matte Vinyl Covers

[ciaranob]

If you want a blank one, the black one I bought came blank as a pack of two. It overlaps on the top and bottom by a 1/4”, but actually makes it easier to place since there is a small amount of overlap. The black matches the dark alcantara well and sits flush. Not sure if the color would match as well with the cloth roof in the 4S/RWD.

https://www.vortexsigns.com/car-decals/porsche/sun-visor-cover-up-stickers-for-porsche1

Good luck!

Ordered my own dark grey vinyl and will cut to fit . Super cheap mod.

Sponsored

 

[Pjjameso]

Are you hating the bright yellow safety notices that all USA Porsche have on the sun visors? I fabricated vinyl sticker covers in dark grey with light grey type. The corners will be cut to a 4mm radius to match the original sticker corners.

They measure 8 x 2.25" and fit over the existing safety sticker perfectly.

$19.50 per set of two with free shipping to the Lower US of A. Only.

Count me in too!

 

[annieland]

Blah, I tried making blackberry ones for mine a few months ago. Ordered vinyl in various dark purple shades which all sucked. Then I tried to color match and bought some leather texture graphics on etsy and started wasting tons of ink on test prints. Everything ended up looking worse than the safety stickers. Never even got to the measuring for the template phase before I gave up in frustration.

If you ever feel like doing different colors or have a source for better vinyl, let me know .

 

[tigerbalm]

Maybe I like the regulatory notices .

Genuine question: are their notices on the driver side in the US? It is only on the passenger side in Europe.

 

[ciaranob]

Maybe I like the regulatory notices .

Genuine question: are their notices on the driver side in the US? It is only on the passenger side in Europe.

Yep both sides and both look equally crap !

 

[enzo5000]

To all the forum members that ordered my visor stickers. They shipped out today 8.04 via USPS 1st. Class Mail. Expect them shortly. Thanks.

 

[vroomer]

Thank you!

 

[gtm]

Thanks. Should be a nice improvement to the interior.

 

[fika]

To all the forum members that ordered my visor stickers. They shipped out today 8.04 via USPS 1st. Class Mail. Expect them shortly. Thanks.

Do you have any more for sale?

 

[ciaranob]

Test fit two simple rectangular cutouts and work pretty darn well - super simple mod and super cheap, bought a roll of quality vinyl for ca $10.

These are again a rough and ready test fit with simple square edges - color matte black as couldn't find a suitable dark enough grey to be a perfect liner match but given the car has a mix of black and grey everywhere it basically works - not sure I'll even bother doing a rounded edge cut as these are at 90%! But my anal attention to detail will prob force me to update them with nicer cuts later !

How 'visible' they are i.e. how much they stand out from background/cloth liner entirely dependent on ambient light. This vinyl again a matte black vs grey, but in reality has a slight satin sheen - either way, a million times better than the ugly warning labels.

Before:

After - I literally cut the pieces and placed them on in less than 10 minutes:

The sharp eyed might also notice my burgundy stripe on my wheel I did some time ago - was not actually planning on keeping that but it looks quite good!:

Most noticeable light angle:

 

[vroomer]

how did you do the steering wheel stripe?

 

[ciaranob]

how did you do the steering wheel stripe?

There are a few posts here somewhere but again, purchase a roll of the nearest color match vinyl you can find (mine from Amazon) and accurately measure and cut a thin strip to wrap it.

KEY is to

1) measure and measure again - don't be afraid to toss your first attempt - you want the strip to not hide (overlap) the side stitching so that it truly looks like colored leather and

2) When installing stretch the strip out as you wrap it around (and think about this when you cut i.e. stretching will thin the width a bit) and it will give a way better fit - leave a 2-4 mm or so overlap and use a drop of super glue or equivalent to ensure the overlap stays bonded (also overlap on bottom and slightly to window side so not at all visible)

Again super simple but as with everything take your time and cut accurately for best results!

 

[enzo5000]

how did you do the steering wheel stripe?

I ordered a few color samples from this joint. Cut them with a razor knife and did the wrap.

https://vvividshop.com/

 

[gtm]

@enzo5000. Received the stickers/covers and have to say I'm pretty pleased with what you have made. Looks just like what you posted and blends very well. So much better than the safety stickers. Thanks.

 

[TLC]

@enzo5000 - if they are still available, I’d like to get a set.

@enzo5000 - I received my set…. Thanks!!!

Sponsored